Bomag MPH362 Asphalt Recycler/Soil Stabilizer
Bomag's MPH362 rear-wheel drive asphalt recycler/soil stabilizer is powered by a 360-hp Cummins N14 water-cooled diesel engine.
• 187-fpm maximum working speeds
• Automatic Power Adjustment System (APA) automatically adjusts forward travel speeds to match application and material being processed
• Three rotor configurations
• 12-inch maximum cutting depth with recycler rotor; 14 inches with stabilizer rotor; 21 inches with deep stabilizer model

Caterpillar PM-201
Caterpillar's PM-201 features a 650-hp Cat C18 engine with ACERT technology.
• 83-inch rotor width
• 12-inch rotor depth
• 41,310-pound operating weight
• Load Sensing Propel System
• Choice of three rotor designs
• High capacity, versatile conveyor

Marini MP 1300 Cold Milling Machine
Marini's MP 1300 cold milling machine has a cutting width of 51 inches and a cutting depth of 12 inches.
• For removing old or damaged roads
• Front-loading foldable conveyor
• Cutting drum is mechanically driven through V-belts
• Interchangeable tool holders
• Center-position drum allows the operator to steer the rear tracks in order to reduce curve radius and mill near curbs

Roadtec RX-900 Cold Planer
The RX-900 cold planer is available with an 860-hp Caterpillar or optional 950-hp Cummins diesel engine.
• Three- or four-track assemblies
• Cuts 14 inches deep and from 7 feet 2 inches to 12 feet 6 inches wide
• 42-inch front load-out conveyor
• Hydrostatic drive for propulsion and conveyor system
• Working speeds up to 128 fpm
• Proportional joystick controlled steering with coordinated, crab, front-only and rear-only modes

Marini MP 2100 Cold Mill
The MP 2100 cold milling machine has a 6-foot 6-inch cutting drum width and a milling depth to 12 inches.
• Cutting drum mechanically driven
• Interchangeable tool holders
• PLC with CAN-BUS technology provides real-time control of major machine functions
• 598-hp diesel engine

Terex RS800 Reclaimer/Stabilizer
The RS800's heavy, unitized mainframe with center-mounted 800-hp Caterpillar engine and cutter distribute the machine's 67,500-pound weight and horsepower for high production.
• V-belt driven
• Four-speed rotor transmission
• Full depth cutter for up to 20-inch cutting depth and 10-foot width

Wirtgen W 35 DC Cold Mill
The Wirtgen W 35 DC small milling machine is used for cold planing small areas for the partial rehabilitation of pavement, milling around manhole covers, and placing and removing road markings.
• Optional short conveyor
• Standard all-wheel drive
• Ergonomic design with operator's station located over the cutter drum
• 14-inch cutting width
• 4.3-inch cutting depth
• 82-fpm operating speed
• 10,031-pound operating weight
• 57-hp engine

Terex/CMI PR950 Roto-Mill
The PR950 Roto-Mill Pavement Profiler cuts up to 15 inches deep with a standard full-lane cutting width of 86 inches at working speeds reaching 170 fpm.
• 950-hp Cummins six-cylinder diesel engine
• Power-band, V-belt direct-drive system
• Quick-mount cutter design with optional 150-inch cutting drum
• Four steering modes
• 42-inch high-capacity conveyor swings 60 degrees to the left or right of center

Caterpillar PM-200
Caterpillar's PM-200 features a 575-hp Cat C18 engine with ACERT technology.
• 79-inch rotor width
• 12.5-inch rotor depth
• 68,122-pound operating weight
• Load Sensing Propel System
• Computerized monitoring system in operator's station

Wirtgen W 2000 Combo Cutter
The new W 2000 Combo Cutter milling machine can change drum widths easily from 24 to 36 to 48 inches in width.
• 565-hp engine
• For shoulder widening
• Cuts zero to 12 inches deep
• Wirtgen Type III Quick Change tooth holder system
• Segmented rear moldboard with independent control and side-shifted material discharge conveyor to maximize material flow