Cold planers, such as this Bradco unit, are used for asphalt and concrete pothole and frost heave repair, curb cutting, pavement texturing and the removal of traffic lane stripes and roadway around manholes.
Units like this FFC Cold Planer can easily perform small milling jobs where large milling machines can't squeeze into or be efficiently used.
Inspect your picks often and replace them when they start looking like the one to the right. Picks generally last up to 150 hours in asphalt applications and up to 30 hours in concrete applications.
Asphalt and concrete picks are two of the most common types out of the hundreds of pick types available.
The value and popularity of skid steer cold planer attachments is becoming increasingly more evident because of the variety of jobs they can assist with. In addition to small milling jobs in which large milling machines can’t efficiently be used, cold planers are an effective tool for asphalt and concrete pothole and frost heave repair, curb cutting, pavement texturing for improved skid resistance and the removal of traffic lane stripes and roadway around manholes. Manufacturers design them to require minimal maintenance. Unfortunately, this has led to many operators completely ignoring most maintenance functions with their cold planer. And, as with almost any attachment, this neglect leads to reduced efficiency and increased wear that creates the need for unnecessary repairs during its life.
“By listening to the noise a cold planer makes and looking at the hydraulic hoses that connect it to the host machine, a perception can be made that they are complicated to maintain,” says Bob Bethards, global account manager for Paladin. “This is not the case at all. Cold planers are one of the easiest machines to maintain, yet many operators still choose to ignore the basic attention they need.”
Production starts and ends with picks
The most critical maintenance function on a cold planer is the proper analysis and replacement of its picks, also known as teeth. The picks fit into holders welded at different angles on the cold planer’s drum. While the drum is designed to promote even wear, typically the outside picks wear first as they cut through the asphalt or concrete, and eventually, this wear starts to affect the cold planer’s overall performance. Check the picks before each use to ensure they aren’t broken or severely worn or “bald” looking.
“Pick wear and replacement time depends on the type of material being cut and the pick quality,” states Bethards. “Typically, picks last between 50 to 150 hours for asphalt applications and 10 to 30 hours for concrete applications. One way to achieve maximum life out of your picks is to rotate the outer and inner picks when they start to show wear. This does not affect the overall performance of the cold planer. It will wear the picks evenly so the operator achieves the ideal cut. This philosophy is the same if you replace a select number of worn picks. It is not necessary to replace the entire drum of picks at once.”
If the picks are not replaced at the appropriate time, both the short- and long-term performance of the cold planer will be affected. As the tips wear beyond a certain point, they can rust to the holder, causing it to severely wear and change the shape of the cutting angle. To fix the holders properly, it requires several hours of precise heating and welding to ensure it is positioned and will cut correctly.
Other general tips about proper pick wear and replacement:
- Adding a water kit to your cold planer reduces dust and can increase pick life by up to 30 percent.
- Replace missing picks immediately or it will cause the surrounding picks to wear at a much faster rate.
- Picks should rotate freely in their holders or they will wear faster.
- Choose picks that are made for your application; while there are hundreds of pick types available, the two most common are “universal” picks that excel in more than 90 percent of applications and concrete picks designed specifically for concrete.
For pick removal, most manufacturers provide a fork tool that slides into a groove on each pick. When in the groove, operators tap the end of this tool with a hammer which pops the pick out. For operators that consistently change out picks, an air compressor, air hammer and punch tool will remove them faster. To insert new picks, flip the fork tool over and follow the same simple procedure. Note: Picks become very hot during operation, so wait until they cool before replacing. Also, don’t hammer on the carbide point of the picks because it can break and cause injury.
Leave no part unchecked
While pick replacement is critical, it’s not the only maintenance check that should be performed on cold planers. Here are some other simple things to be aware of. The time periods noted below are specifically related to Paladin’s Bradco and FFC Cold Planers and many other common brands. Be sure to read your manual for specific maintenance time periods for your unit.
- Ensure all nuts, bolts and other fasteners are in place, properly tightened and performing their specified function.
- Check all hoses for wear and/or damage and ensure there are no leaks.
- Inspect all quick disconnect areas for damage.
- Clean debris from all valves and hoses to avoid hydraulic system contamination.
- Ensure that the case drain coupler is completely engaged and the hose is not kinked or crushed; a restricted case drain flow can blow the shaft seal on the motor.
- Ensure the skid steer hydraulic system is at an adequate level of hydraulic oil.
- Keep as much outside debris out of the drum as possible.
Every 40 Hours Or Periodic Maintenance/Tips
- Grease all moving parts, including wheel bearings, hydraulic cylinder pivot pint, side shift wear areas like flat bars or side shift rods and the depth plates (also known as skids); always wipe off excess grease from fittings because it will collect dirt and increase wear.
- Check the planetary for leaks and call your dealer immediately if a fix is necessary.
- Perform the initial oil change after 50 hours of operation and once per year or every 1,000 hours after that.
“Lastly, one of the most important things to remember is don’t rush your cold planer,” says Bethards. “The unit will do the work, but you have to match the speed to the cut depth and application. Think of it in terms of inches and feet, not miles per hour. Don’t push it too fast or you will add significant wear to your picks, the rest of the attachment and the skid steer.”
As always, read your cold planer manufacturer’s operation manual thoroughly before using. The operation manual also commonly includes troubleshooting tips in case problems occur.