Concrete Contractor cuts through the mass of information and delivers only the best, most practical and newsworthy material to the concrete contractor. In each issue, readers benefit from information on concrete equipment, current technology, job-site solutions, tips on staying competitive, finance, insurance and a host of other hard-hitting material.
The Grip-Rite PROLOK High Chairs feature a locking head that raises rebar or reinforcing wire mesh to the proper position and secures rebar intersections with no tie wire or bar ties.
Stackable for multi-layer grids
Engineered to fi No. 3 through...
All-aluminum frame big panel with composite face sheet
Lightest crane-set, cast-in-place big panel
Superior durability over wood with high-quality finish
Largest range of sizes: widths 6 in. to 21 ft.; heights 1- to 12-ft.
No consumables, ties are...
The Lenton Form Saver eliminates protruding dowel bars in segmental pours and temporary openings.
Provides continuity and structural integrity to reinforced concrete
Develops strength requirements independent of concrete cover
Contractors can use Sonovoid round concrete void forms to create voids in concrete floor and roof slabs, bridge decks, beams, piers and pile projects.
Less concrete, steel and supporting members results in cost savings
Use on cast-in-place or...
Thermomass building insulation system is used in concrete cast-in-place, tilt-up and precast walls to create energy-efficient concrete sandwich walls.
Results in load-bearing, durable and moisture-resistant walls
Insulation system uses Dow Styrofoam...
Dokaflex is a pre-engineered slab forming system with high capacity components that greatly increases spacing between the members and requires less material when compared with traditional 4x4 wood shoring.
Flexible system adapts to changing floor...
Poly Meta Forms system utilizes plastic forms in conjunction with steel stake pockets to place all types of concrete.
Light weight makes it easy to set, strip and transport
Moisture-resistant will not rot, splinter or rust
Forta-Ferro is a synthetic macro fiber reinforcement used to reduce plastic and hardened concrete shrinkage, improve impact strength, and increase fatigue resistance and concrete toughness.
Designed to mix and finish well, even at high dosages
Use the Aluminum Ashlar Stone concrete form to create decorative walls and foundations without the need of a formliner.
Durable aluminum sheets with the imprint of a deep ashlar stone pattern
Compatible with any traditional aluminum forming system
Positive reinforcing steel positioning device used to control concrete coverage and steel location in concrete walls designed with two mats of reinforcing
Manufactured to project specifications regarding minimum coverage, steel size, orientation of...
A 12-lb. roll forms the same amount of concrete as 900 lbs. of lumber.
Can be used as a complete footing form or as an edge form
Prevents rising damp
Adapts to uneven ground
Residential and commercial versions available
This "one concept" approach to slab production eliminates the materials, transportation and clean-up of temporary forming methods and form anchors as well as the need for any dowel placement components.
Lightweight PVC, cast-in-place screed rail is...
The Model FS-600 portable rebar cutter/bender will both cut and bend up to 3/4-in. (#6) rebar.
Plugs into a standard 110-volt outlet
Fabricate stirrups, hooks, 3-D bends and cut bars to length
Convenient carrying handles for...
The rebar bender attachment comes with five mandrels that provide the ability to bend rebar into a variety of angles and repeat bends for added consistency and efficiency.
Bend rebar up to a #6 grade up to 200 degrees
Remote attachment control for...
The new 36Z Truck-Mounted Concrete Boom Pump has a reduced weight, a more user-friendly design and offers increased ease of service.
Gross vehicle weight of 51,500 lbs. (26 tons)
30 percent more deck space than previous models...
The BP50a backpack concrete vibrator now has CE Mark approval certifying it has met EU consumer safety requirements. The vibrator features a totally enclosed rotary throttle that prevents wet concrete from entering and clogging the throttle...
Two models of Loop Belt truck-mounted conveyors offer contractors concrete placing options with set-up capability in an area with less than 18 ft. of overhead clearance.
LB32T4 has a horizontal reach of 32 meters, four telescopic sections, an...
The SC-75 rubber track concrete buggy travels through wet, muddy ground conditions, operates in rough, uneven terrain and maneuvers within loose sand and gravel.
Features a 16-cu.-ft. capacity
90° dump angle
22-hp Robin gas engine...